×
Quick Equipment Search
Equipment Fliter










used search tag used search tag

TE 4X2 ELECTRIC UTILITY VEHICLE

Utility Vehicle

  • Quiet electric operation
  • Wide stance for enhanced stability
  • Best in class cargo box
  • Zero emissions/zero fuel consumption
Starting At:15,499.00

View Product Brochure



Features



Drive systemDrive system
Directional change control switchDirectional change control switch

The Gator™ TE Utility Vehicle features a motor powered by a 48-V electrical system.

  • This electrical system provides plenty of power to accelerate faster, carry loads, climb hills better, and perform evenly until recharge

Through the use of a separately excited controller, the Gator TE offers the following unique features:

  • Dynamic braking
    • The motor brakes when the operator lets off the accelerator; it is not a substitute for the brakes
  • Overspeed control
    • Reduces exposure to high-speed situations even when descending a hill; under normal conditions with a light load, the vehicle will not freewheel down an incline
  • Roll away
    • The electronic brake limits the vehicle speed to approximately 3.2 km/h (2 mph) and prevents the vehicle from freewheeling down a grade when left unattended
  • Reduced speed in reverse
    • Controls the vehicle speed to approximately 13 km/h (8 mph) without the loss of torque
  • Anti-rollback
    • When stopped on a grade, this feature prevents the vehicle from freewheeling in the opposite direction of the original travel direction
  • Regeneration
    • Energy is transformed back into the batteries when the vehicle travels faster than the set maximum speed; regeneration also occurs when dynamic braking is engaged; an estimated 3 percent to 5 percent regenerative energy is put back into the batteries during a day of work
  • Diagnostics
    • An onboard computer diagnoses the electrical system; using a flashing indicator light, a sequence of flashes indicates where the controller is having problems communicating
  • Speed control
    • The controller is set for a vehicle speed of 24.1 km/h (15 mph)
  • Key-off control
    • Permits the function of the interlock and safety features with the key in the off position
  • Directional change control
    • When switching from forward to reverse, the machine will come to a complete stop and then changes directions; this prevents a whiplash effect and potential high stress on the drivetrain

Power is transferred through a transaxle with helical gearing for low gear noise.

Onboard battery charger (detail)Onboard battery charger (detail)
Battery charger located under passenger seatBattery charger located under passenger seat

The Gator™ TE is equipped with an Underwriters Laboratories Inc. (UL) approved onboard charger. Located under the passenger seat, the onboard charger allows the user to charge their TE from any location containing a wall receptacle. This saves the user time, as they do not have to travel back to the maintenance area for charging; charging can be done anywhere.

The onboard charger is designed with a wide input voltage range from 85 - 265 VAC, making it capable for worldwide application. Power factor correction and 12A maximum current draw ensures the charger will work reliably from any power outlet in the world, even through surges and sags.

Improved run time

The onboard charger features advanced temperature sensor technology that improves the information flow coming in and out of charger. The batteries are allowed to charge more fully than they were ever able to before; this can improve run time by up to 75 percent (depending on use cycle).

 

Important safety features of the charger are as follows:

  • Vehicle ignition interlock
    • Prevents the vehicle from being driven while connected to the charger
  • Automatic shutoff
    • Battery charger automatically shuts off after reaching the full charge
External charger plug and light-emitting diode (LED) charge indicator
#
#

The Gator TE is equipped with an external AC input IEC connector on the driver side of the vehicle to allow the flexibility of where the charger cord is stored. There is a multicolor LED indicator for low charge, more than 80 percent charge, full charge, or fault.

The heavy-duty design with arc-welded uni-body construction provides strength and manufacturing tolerance control.

Side-by-side seatingSide-by-side seating
#

Many of the Gator™ TE's standard features offer the operator and passenger a smooth, comfortable ride.

  • Side-by-side seating provides room for the operator and one passenger
  • Hip restraints serve as a handhold and help to keep the operator and passenger in their seats over rough terrain
  • Professional high-back cushioned seats are position-adjustable and provide additional comfort and support
  • Both seats tilt forward for dry storage and ease of service
Walk-through platformWalk-through platform
#

The Gator TE's controls and improved walk-through platform provide easy entry/exit for both operator and passenger.

  • Glove box is located in the dash to provide a convenient storage area for small tools and the operator's manual
  • Grab bar is provided for the passenger
  • Automotive-style controls for easy operation
  • Center-mounted key switch
  • Steering wheel is moved forward to provide more room for the operator
Deluxe cargo box (TX 4X2 shown)Deluxe cargo box (TX 4X2 shown)
Deluxe cargo box, tailgate lowered (TX 4X2 shown)Deluxe cargo box, tailgate lowered (TX 4X2 shown)

The deluxe cargo box consists of a 15 percent glass-filled polypropylene composite material that eliminates rust and dents and reduces noise.

Deluxe cargo box tailgate
Tailgate handleTailgate handle
Tailgate lowered to 150 degreesTailgate lowered to 150 degrees

The tailgate can be opened or removed for easier cleanout and to carry longer items. The tailgate has been improved, features truck-like performance, and can be operated with one hand.

 

The standard installed lanyards can also be removed to lower the tailgate to 150 degrees for convenient loading and unloading tasks.

Deluxe cargo box tilt
Integrated handle for manual cargo-box tiltIntegrated handle for manual cargo-box tilt
Gas assist (A) and prop rod (B) (TX 4X2 shown)Gas assist (A) and prop rod (B) (TX 4X2 shown)

The deluxe cargo box is easier to latch, unlatch, raise, and lower with the integrated handle design and gas assist (A). Optional factory- or dealer-installed cargo box power lift is also available.

 

A prop rod (B) is provided to hold the box in the upright position for operator convenience, as well as limit box pivot travel.

Integrated tie-down points
Integrated tie-down point in cargo box bedIntegrated tie-down point in cargo box bed
Additional tie-down points (TH 6X4 shown)Additional tie-down points (TH 6X4 shown)

The deluxe cargo box offers integrated tie-down points for increased versatility. Tie-down points are located in the following areas:

  • Four corners inside the cargo box bed
  • Four points on the load guard directly behind the operator station (A)
  • Tie-down bars on either side of the cargo box (B)
  • Six points on the underside of the cargo-box frame (circled)
Converting deluxe cargo box to a flat bed
Deluxe cargo box converted to a flat bedDeluxe cargo box converted to a flat bed

The deluxe cargo box easily converts to a flat bed. The flatbed configuration allows loading larger cargo.

NOTE: Cargo box shown on Gator TX. Gator TE rear axle configuration is different.

Optional accessories
Brake and taillightBrake and taillight
Bedmat—protects the steel floor from dentsBedmat—protects the steel floor from dents

Optional accessories for the deluxe cargo box include:

  • Factory-installed brake and taillight
  • Factory-installed spray-in liner (not shown)
    • Improves skid resistance and surface abrasion protection
  • Cargo box bed mat
  • Cargo box power lift (not shown)
  • Wide variety of attachments that connect to cargo box rails

 

Specifications

 

Box capacity

Volume0.46 m3 (16.4 ft3)
Weight227 kg (500 lb)

 

 

Box dump angles (degrees)

Manual dump43 degrees +/-1
Power dump43 degrees +/-1


CAUTION: Carrying extra-long cargo that extends beyond the box can adversely affect stability.

Specifications


Compare the specifications of up to 4 models

Key Specs te-4x2-electric-utility-vehicle
Current Model
Electrical system48 volt w/8 Trojan T-145 batteries
Brake typeDual rear wheel mechanical drum
Speed0-13 (Can be adjusted with handheld programmer) mph
24.1 km/h
Front suspensionIndependent, spring over shock, single A-arm
Payload capacity900 lb
408 kg
Towing capacity500 lb
227 kg
Cargo box volume16.4 cu ft
0.46 m3
Charger typeHigh frequency switched-mode
Drive system
MotorWound direct drive, 48VDC separately excited
ControllerSeparately excited, 400 amp max., Anti-roll away braking and alarm. Antistall motor protection. Regenerative braking. Diagnostic indicator. Full torque, reduced speed reverse.
Transaxle16.99:1 ratio with helical gearing
Electrical system48 volt w/8 Trojan T-145 batteries
Speed0-13 (Can be adjusted with handheld programmer) mph
24.1 km/h
Gear selectionForward, Neutral, Reverse
Torque converterN/A
BatteryTrojan T-145
Extended run time batteryNot Available
Brakes
TypeDual rear wheel mechanical drum
Park brakeHand operated, multi-latch
Tires
Front2 - 22x9.5-10, 4-ply high-flotation turf
Rear2 - 24x12-10, 4-ply high-flotation turf
Dry weight1302 lb
Suspension and Steering
FrontTotal Travel
5 in.
127 mm
Independent, spring over shock, single A-arm
RearTotal travel
Not Available
2 hi-flotation, low pressure tires
SteeringRack and pinion
Dimensions
Height44.5 in.
1130 mm
Width60 in.
1524 mm
LengthWithout bumper
104.9 in.
2664 mm
With bumper
107.4 in.
2728 mm
Ground ClearanceUnder transaxle
196 mm
7.7 in.
Under foot platform
7.3 in.
185 mm
Front tread centers50 in.
1270 mm
Rear tread centers48 in.
1219 mm
Wheelbase76.4 in.
194 cm
Vehicle weight1389 lb
630 kg
Turning clearance circle22 ft
6.7 m
Payload capacity900 lb
408 kg
Towing capacity500 lb
227 kg
Seats
TypeProfessional high back bucket, tilt forward
Seating capacity2
Seat adjustmentOptional
Cargo box
Length45 in.
1143 mm
Width52 inside in.
1321 inside mm
Depth12 in.
304.8 mm
Capacity500 lb
227 kg
Volume16.4 cu ft
0.46 m3
Height above ground30 in.
762 mm
MaterialPolypropylene side panels and tailgate; steel floor and load guard
TailgateHinged at bottom, removable; side panels are removable
DumpManual, power lift (optional)
Ground pressure
Frame
Charger
TypeHigh frequency switched-mode
Input voltage120 VAC 60 Hz.
Input amperage (Nominal)12 A (15 A breaker max.)
Output voltage48 VDC nominal
Output amperage21 ADC
AC input connectorIEC320/C14
AC power cord94 in.
2.4 m
Machine
Fenders and hood

Accessories and Attachments

Alternator

High-capacity alternator kitHigh-capacity alternator kit

This kit provides the additional amperage output required while operating certain attachments at low idle for long periods of time.

 

At high idle, the kit will supply up to an additional 45 amps and, when combined with the existing output, will provide up to 60 amps cumulative.

 

The heavy-duty DENSO® alternator in the kit is completely enclosed, sealing out all possible contaminants. This alternator has been tested in diverse conditions to ensure durability.

 

DENSO is a U.S.-registered trademark of DENSO Corporation.

Backup Alarm

Bumper

Front bumper (includes front receiver hitch)Front bumper (includes front receiver hitch)

Composed of strong tubular steel, the front bumper protects the front of the Gator™ Utility Vehicle.

Front bumper/brush guard Front bumper/brush guard

Composed of strong tubular steel, the heavy-duty bumper and brush guard protect the unit from front impacts, as well as add increased protection to the grille and headlights.

Compatible with:

  • TS, TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
Front fender guardFront fender guard
#

The front fender guard is composed of strong tubular steel that protects the unit from side impacts.

 

NOTE: The front bumper is standard on the Gator™ TH 6x4 Diesel.

 

The front fender guard requires BM23458 front bumper or BM23459 heavy-duty bumper/brush guard.

Rear bumper kit (TH 6X4 shown)Rear bumper kit (TH 6X4 shown)

The rear bumper offers stylish, heavy-duty rear protection to the vehicle.

Compatible with:

  • Model year 2011 and later Gator™ XUV 625i, XUV 825, and XUV 855 Utility Vehicles
  • Model year 2010 and later Gator TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
  • Model year 2018 and later Gator XUV835 and XUV865 Utility Vehicles

Cargo Box

Cargo box pail holderCargo box pail holder
Cargo box pail holderCargo box pail holder

The 5-gal. (18.9-L) pail holder is ideal for operators who want to maximize the work capability of their Gator™ Utility Vehicle. The 5-gal. (18.9-L) pail holder keeps pails in place within the cargo box, ensuring that they stay safe and secure. Featuring the quick-clamp mounting system, it mounts easily to the cargo rails of the cargo box with just one clamp.

Cargo bed extenderCargo bed extender
Cargo bed extenderCargo bed extender

The cargo bed extender conveniently extends the rear of the cargo bed, and also acts as a cargo box divider when it is flipped inside of the cargo box. The cargo bed extender easily flips in or out with the use of quick-pull pins.

Deluxe cargo box bed matDeluxe cargo box bed mat

The deluxe cargo box bed mat not only protects the steel floor from scratches and dents, it also provides additional cushioning and slip resistance to items being hauled in the cargo box.

Cargo box divider located at rear of cargo bedCargo box divider located at rear of cargo bed
Cargo box divider located at front of cargo bedCargo box divider located at front of cargo bed
Speedrail lock in the unlocked postionSpeedrail lock in the unlocked postion
Speedrail lock in the locked postionSpeedrail lock in the locked postion

The Gator™ XUV Series can be equipped with an optional divider for the deluxe cargo box. The dividers can be positioned at the front or rear of the cargo box bed. To change positions of the dividers, simply release the speedrail locks by hand and slide into new position, then close the locks to secure the dividers.

Cargo box power lift kitCargo box power lift kit

The power lift kit utilizes an electromechanical actuator for easy raising and lowering of the Gator™ cargo box.

 

A switch is conveniently located on the dash to operate the power lift kit. As with all Gator electrical kits, the power lift kit ties into the vehicle's wiring harness for quick installation.

 

Compatible with the following utility vehicle:

  • Gator TE (if equipped with 48V to 12V converter), TX, TX Turf Utility Vehicles
Cargo box side extension kit Cargo box side extension kit
#

The cargo box side extension kit expands the versatility of the Gator™ Utility Vehicles and is ideal for those who are enhancing their property and landscape. The extensions allow operators to haul twice the volume (not to exceed cargo box weight capacity) of light material such as grass clippings and mulch. 

 

Product features include:

  • Four-sided structure that increases cargo box side height to 533 mm (21 in.) and volume to 0.74 m3 (26 cu ft)
  • Mounted on the sides and front with hardware, while the tailgate can be attached or removed without tools
    • Tailgate pivots at the top (similar to a dump truck) for ease of dumping loose material
  • Laser-cut, heavy-gauge, powdered-coated steel provides excellent durability
  • Compatible with all model year 2011 to current Gator XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, and M-Gator A2 Utility Vehicles
  • Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
  • Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles.
  • Compatible with Gator cabs and bedliner

 

NOTE: The cargo box side extensions are not intended to increase the rated cargo box carrying capacity per the vehicle specification.

Label kit for toolboxes (Green & Yellow) - BM26220

The remote cargo box release kit makes opening the cargo box much easier due to limited hand clearance space between the deluxe cab and deluxe cargo box. This kit includes a bracket assembly that quickly mounts to the deluxe cargo box.

It is compatible with the following vehicles:

  • TH 6x4 Gas, TH 6x4 Diesel, TE, and TX Utility Vehicles with a deluxe cargo box and equipped with a deluxe glass cab and manual cargo box lift (no power lift).
Side storage boxSide storage box
#

The side storage box offers over 0.03 m3 (1 cu ft) of storage space to keep valuable items dry and secure.

 

The side storage box is:

  • Lockable
  • Weather resistant

It is compatible with:

  • Gator™ TS, TX, TX Turf, TE Utility Vehicles

  • XUV 620i and 850D Utility Vehicles

  • HPX Gas and Diesel Utility Vehicles

Not compatible with Sunshade

NOTE: The side storage box fits the driver side only.

Tool rackTool rack
Tool rack with toolsTool rack with tools

The side tool rack enables the user to maximize the use of their cargo box by carrying long-handled tools, such as trimmers, shovels, and rakes, on the outside of the box. The holders are adjustable, allowing the users to carry a wide array of items in the racks.

Tool rack holder detailTool rack holder detail
Adjusting the tool rack holder Adjusting the tool rack holder
Tailgate with brake and tail lightsTailgate with brake and tail lights

This tailgate kit with brake and tail lights is specifically designed for compatibility with the top and side-door toolboxes (BM26162 and BM26160).

 

The tailgate can be installed in minutes once the toolbox and tail lights are installed by bolting to the tailgate bracket.

 

Optional label kits are designed to fit with this tailgate:

  • BM26220 – green and yellow
  • BM26218 – olive and black
  • BM26219 – camo

The tailgate is compatible with the following Gator™ Utility Vehicle models:

  • TX
  • TX Turf
  • TE
  • TH
  • XUV625i
  • XUV825i
  • XUV825i S4
  • XUV855D
  • XUV855D S4

Carts

21 Steel Utility Cart21 Steel Utility Cart

The 21 Steel Utility Cart is the ideal companion for the Gator™ Utility Vehicle:

  • 454-kg (1000-lb) load limit
  • Dump angle of 35/40 degrees
  • Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
  • Large pneumatic tires
    • Provide good flotation in mud, sand, and other wet or soft areas
    • Flex over bumps and ruts for a smoother, more controlled ride
    • Minimize ground compaction to save turf and prevent ruts in soft ground
  • Unique bracket less tailgate means no side channels to obstruct materials when emptying
  • When shoveling, recessed flat bolt heads stay out of the way
  • Heavy-duty, reinforced one-piece solid undercarriage
  • Contoured corner bed design
  • Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1-7/8-in.) ball hitch, including Gater™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

21 Steel Utility Cart
Order number: LPUT21JD

Cover

Gator coverGator cover

The cover provides heavy-duty protection for Gators.

  • Dual reinforced air vents let air circulate and help to prevent ballooning in windy conditions
  • Reinforced rear corners for added stability
  • Fabric-coated for maximum water resistance and repellency
  • Elastic shock cord in the bottom hem for a quick custom-like fit
  • Large size fits all standard and traditional series Gators
Ordering information

Please contact the local John Deere dealer for availability and pricing information.

 

Gator cover (large)
Order number: LP93547

Deluxe seat coverDeluxe seat cover

The deluxe thick-cushioned seat cover provides superior protection, all-day riding comfort, and lots of storage.

  • Two side mesh-stuff beverage pockets hold drinks, and a big rear zippered cargo pocket and mesh-stuff pocket keep tools and gear readily available
  • Little zippered side key
  • Elastic cord in the hem provides a custom fit
  • Handy fabric storage case and John Deere key ring
  • Three-year warranty
  • Large, fits backrests up to 457 mm (18 in.)
Ordering information

Contact the local John Deere dealer for availability and pricing information.

Deluxe seat cover (large)
Order number: LP92634

Seat coverSeat cover

The cover protects unused seats and renews worn seats.

Cushioned seat for extra comfort

  • Four convenient pockets keep tools and gear within reach
  • Central water drain hole keeps water from pooling
  • Elastic cord at hem for a custom fit
  • Medium size fits backrests up to 381 mm (15 in.)
  • Large size fits backrests up to 457 mm (18 in.)
  • Two-year warranty
Ordering information

Contact the local John Deere dealer for availability and pricing information.

Seat cover (large)
Order number: LP92334

Camo seat cover (large)Camo seat cover (large)
  • REALTREE® HARDWOODS HD® pattern is so neutral it simply disappears into virtually any outdoor setting
  • Two side mesh-stuff beverage pockets hold tools, and a large rear zippered cargo pocket and mesh-stuff pocket keep tools and gear readily available
  • Elastic cord in the hem provides a custom fit
  • Handy fabric storage case and John Deere key ring
  • Large size fits backrests up to 457.2 mm (18 in.)

REALTREE HARDWOODS HD is a U.S.-registered trademark of Jordan Outdoor Enterprises Limited.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

Camo seat cover (large)
Order number: LP92333

Vehicle coverVehicle cover
  • Provides year-round weather protection to a vehicle equipped with an operator protection system (OPS) or full enclosure (cab)
  • Heavy-weight polyester fabric for maximum durability and resistance to tear 
  • Polyurethane-coated for maximum water resistance and repellency 
  • Dual reinforced air vents let air circulate and help to prevent ballooning in wind
  • Reinforced rear corners for added durability  
  • Elastic shock cord in the bottom hem for a quick custom-like fit
  • Compatible with the following models:
    • Traditional Series models (TS, TX, TX Turf, TH 6x4, TH 6x4 Diesel, and TE when equipped with a full enclosure), and HPX 4x4, HPX 4x4 Diesel, HPX 4x4 Trail, XUV 620i, and XUV 850D (with OPS or deluxe cab structure and accessories)
    • Gator™ model year 2011 XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles (with OPS or deluxe cab structure and accessories)
Ordering information

Please contact the local John Deere dealer for availability and pricing information.

 

Vehicle cover (full size—cab or structure)
Order number: LP93107

Camo vehicle coverCamo vehicle cover
  • REALTREE® HARDWOODS HD® pattern is so neutral it simply disappears into virtually any outdoor setting
  • Provides year-round weather protection to a vehicle that is equipped with an operator protection system (OPS) or full enclosure (cab)
  • Heavy-weight polyester fabric for maximum durability and resistance to tear
  • Polyurethane (PU) coated for maximum water resistance and repellency
  • Dual reinforced air vents let air circulate and help prevent ballooning in the wind
  • Reinforced rear corners for added durability
  • Elastic shock cord in the bottom hem for a quick custom-like fit
  • Compatible with the following models:
    • Traditional Series models (TS, TX, TX Turf, TH 6x4, TH 6x4 Diesel, and TE when equipped with a full enclosure), HPX 4x4, HPX 4x4 Diesel, HPX 4x4 Trail, XUV 620i, and XUV 850D (with OPS or deluxe cab structure and accessories)
    • Gator model year 2011 XUV 625i, XUV 825i, and XUV 855D Utility Vehicles (with OPS or deluxe cab structure and accessories)

REALTREE HARDWOODS HD is a U.S.-registered trademark of Jordan Outdoor Enterprises Limited.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

Gator OPS and deluxe cab camo cover
Order number: LP93103

Drawbar

48-mm (1-7/8-in.) hitch ball48-mm (1-7/8-in.) hitch ball

The 48-mm (1-7/8-in.) ball hitch attaches to the drawbar or rear hitch to allow towing.

 

The ball hitch is available through Service Parts.

48-mm (1-7/8-in.) ball hitch shown48-mm (1-7/8-in.) ball hitch shown

The 51-mm (2-in.) ball hitch attaches to the drawbar or rear hitch to allow towing.

 

The ball hitch is available through Service Parts.

Hitch drawbar kitHitch drawbar kit

This kit includes a 32-mm (1.25-in.) solid steel drawbar, galvanized cross pin, and hitch pin kit. It does not include a ball hitch.

 

The drawbar kit may be used on the front or rear of the utility vehicle.

Front Rack

Guards

Cargo box fender guard kitCargo box fender guard kit
#

The cargo box fender guards offer enhanced styling in addition to heavy-duty protection to the side of the cargo box:

  • Compatible with all model year 2011 and later Gator™ XUV 625i, XUV 825i, and XUV 855D Utility Vehicles.
  • Compatible with model year 2013 - current Gator XUV 825i S4 and XUV 855D S4 Utility Vehicles.
  • Compatible with model year 2010 and later Gator TX, TX Turf, and TE Utility Vehicles.

NOTE: BM22767 rear bumper is required to install the cargo box fender guards.

Horn

Horn componentsHorn components
Horn switchHorn switch

Kit includes:

  • Horn
  • Mounting brackets
  • Wire harness and switch

The switch mounts on the dash of the vehicle. The wiring harness connects to the main vehicle harness.

 

Compatible with following vehicles:

  • CS, CX, TS, TX, TX Turf, TH 6x4, M-Gator™ A1 

NOTE: This kit comes less grease.

Lighting

The beacon light is ideal for those who are looking to provide additional awareness for bystanders.

Beacon light - 48 V mounted on cabBeacon light - 48 V mounted on cab
Beacon light - 48 V mounted on vehicleBeacon light - 48 V mounted on vehicle
Beacon light - 48 V rocker switchBeacon light - 48 V rocker switch

The beacon light kit - 48 V is available for Gator™ Utility Vehicles equipped with a deluxe hard or soft cab and can also be mounted without a cab:

  • Dual voltage compatible, 12 V (TS, TX, TX Turf, TH) or 48 V (TE)
  • Dash-mounted on/off rocker switch
  • LED strobe light
  • Durable nylon housings and scratch-resistant acrylic lens
  • Sealed against water, dust, and corrosion
  • UL-recognized SAE J845 (class 3)
  • Flash rate of 60 + 10 fpm
  • Low current draw of 0.2 amp
  • Use of LED technology provides excellent resistance to damage from external shock and 100 times the useful life of an incandescent lightbulb
  • Measures 1.8 m (74 in.) off the ground when mounted to the hard or soft cab and when mounted to the upright
  • Compatible with Gator TS, TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
Beacon light kitBeacon light kit

Rotary light provides excellent visibility to vehicle bystanders:

  • Especially useful for working around properties and job sites
  • Sturdy design allows the Gator to be hauled on a trailer forward or backward at highway speeds with the light installed
  • Contains a breakaway mounting system
    • Sealed package (waterproof)
    • Amber lenses are rugged, shatter-resistant poly material
  • Light assembly bolts to the rear of the cab frame
  • Convenient overhead mounted on/off rocker switch for easy operation
  • As with all Gator electrical kits, the light kit ties into the vehicle's wiring harness for quick installation

Compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • All Gator HPX model year 2004-current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator A1 when equipped with a hard-door cab and electrical kit
Brake and taillight kitBrake and taillight kit

The integrated brake and taillight kit offers an updated, stylish design in addition to being highly visible in all light conditions.

Compatible with:

  • Model year 2017 - current Gator TX, TX Turf, and TH 6X4 Utility Vehicles equipped with the deluxe cargo box
Front marker lightFront marker light
Brake and taillightsBrake and taillights

The deluxe light kit includes the following:

  • Backup lights
  • Four-way flashers
  • Turn signals
  • Brake lights
  • Taillights
  • Front position lights

 

The kit also includes required dash-mounted switches.

 

NOTE: Not intended for use on public roadways.

Front work light kitFront work light kit

Two 55-W halogen lights provide superb visibility for nighttime operation:

  • Especially useful for working around properties and job sites
  • Sturdy design allows the Gator to be hauled on a trailer forward or backward at highway speeds with the lights installed
  • Light assemblies bolt to the front of the cab frame, creating a consistent lighting pattern
  • Convenient overhead-mounted on/off rocker switch for easy operation
  • As with all Gator electrical kits, the light kit ties into the vehicle's wiring harness for quick installation

Compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • All Gator HPX model year 2004-current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator A1 when equipped with a hard-door cab and electrical kit
Interior light kitInterior light kit
  • Interior overhead light provides visibility for nighttime operation
  • Light assembly bolts into the overhead panel of the cab for automotive styling
  • Contains an on/off rocker switch for easy operation
  • As with all Gator electrical kits, the light kit ties into the vehicle's wiring harness for quick installation

Compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles
  • All Gator HPX model year 2004 to current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • Traditional Series—TS, TX, TX Turf, and TH 6x4 when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator A1—when equipped with a hard-door cab and electrical kit
Rear work light kitRear work light kit

One 55-W halogen light provides superb visibility for nighttime operation:

  • Especially useful for working around properties and job sites
  • Sturdy design allows the Gator to be hauled on a trailer forward or backward at highway speeds with the lights installed
  • Light assembly bolts to the rear of the cab frame, creating a consistent lighting pattern
  • Convenient overhead-mounted on/off rocker switch enables easy operation
  • As with all Gator electrical kits, the light kit ties into the vehicle's wiring harness for quick installation

Compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • All Gator HPX model year 2004 to current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame and electrical kit
  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator A1 when equipped with a hard-door cab and electrical kit
Brake and taillight protectorBrake and taillight protector

The brake and taillight protector offers increased protection to the taillight assembly from incidental contact.

Mirrors

Exterior mirror kitExterior mirror kit
  • Rigid design allows the Gator™ to be hauled on a trailer forward or backward at highway speeds with the mirrors installed
  • Adjustable mirror assembly bolts to the cab structure
  • Contains a breakaway mounting system

Compatible with the following vehicles:

  • Traditional Series - TS, TX, TX Turf, TE, and TH 6X4 - when equipped with a soft-door or hard-door cab
  • M-Gator™ A1 when equipped with a hard-door cab

Operator''s Manual And Decal Kit

Operator''s Station

Shown on TH 6x4Shown on TH 6x4
Shown on TH 6x4 - doors and windshield openShown on TH 6x4 - doors and windshield open

The deluxe glass cab includes front windshield (excluding wiper), glass doors, and glass rear window.

For use on the following Gator Utility Vehicles:

  • TS, TX, TH 6X4 Gas, TH 6X4 Diesel, M-Gator A1, TE, and TX Turf

Features

  • Rollover protective structure (ROPS) certified
  • Rear glass window opens to allow ventilation
  • Front windshield can be opened in two positions for ventilation
  • Gas cylinders counter-balance the weight of the windshield when opened
  • Lower front windshield panel is removable without tools, allowing access to remove vehicle hood for service
  • Lockable glass doors
  • Wide variety of individual accessories allows for customizing of cabs

NOTE:

  • BM21653 remote cargo box release kit is required if vehicle is not equipped with cargo box power lift. BM21653 is for use with the TS and steel cargo boxes and is not compatible with model year 2010 to current utility vehicles (deluxe cargo box) or M-Gator A1.
  • BM24804 remote cargo box release kit is required for model year 2010 to current utility vehicles with the deluxe cargo box and is not equipped with a cargo box power lift.
  • Heavy-duty front suspension kit is recommended.
Electrical kitElectrical kit

Required to power electrical cab accessories, this kit includes an overhead console to mount switches that operate electrical accessories, the main cab harness, the 30-A fuse holder, the 30-A fuse, and the roof padding.

 

Compatible with the following vehicles:

  • Traditional Series—TS, TX, TX Turf, TH 6x4, and TH 6x4 Diesel when equipped with a soft-door or hard-door cab
  • M-Gator™ A1—when equipped with a hard-door cab
Rubber floor matRubber floor mat

Washable mat protects the floor and minimizes dust, debris, and noise in the operator station.

 

Compatible with Gator™ TS 4X2, TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TX Turf, and TE Electric-145 Utility Vehicles.

The forced-air heater kit uses a dash-mounted heater powered by gasoline from the vehicle's fuel system. Since the heater is using fuel instead of warm coolant from the engine to generate heat, the cab heat is available more rapidly. The desired cab temperature can be reached with or without the engine running.

  • Dash-mounted, five-position control dial to adjust for operator comfort
  • Position 1 is off
  • Positions 2 to 5 offer four heat levels (low, medium, high, and boost, respectively)
  • LED indicator light for operation
  • Dash-mounted, directional louver provides windshield defrosting and complete operator comfort
  • Second outlet provides heat to the foot well area
  • Compatible with the following T Series models: TS, TX, TX Turf, and TH 6x4 (gas)

Specifications

  • Heat output of 0.8 kW to 2.2 kW (2900 Btu/hr to 7500 Btu/hr)
  • Gasoline consumption of 0.10 L/hr to 0.27 L/hr (0.02 gph to 0.07 gph)
  • Air throughput of 0.85 m3/min to 1.42 m3/min (30 cfm to 70 cfm)
  • Power consumption at startup of 250 W (at 12 V)
  • Power consumption in operation of 8 W to 30 W
Operation of forced-air heater

Upon startup, the heater's control module runs a self-diagnostic check for safety. Then, the blower begins to increase speed as fuel is fed into the burner. Once the combustion process has stabilized, the glow plug is switched off. The heater continues to run until the thermostat senses the temperature has reached the setting on the control dial.

 

The heater will then switch to the next lowest setting. The heater will return to the higher setting as the temperature drops below the setting on the control dial. If the heater switches itself off, it will automatically restart when the temperature drops below the setting on the control dial.

 

If the heater's control module senses an incorrect air-intake volume, incorrect exhaust volume, incorrect fan speed, flame absence, flame loss, overheating, control dial failure, sensor failure, blower failure, glow plug failure, fuel pump failure, incorrect voltage, short-circuit or control module failure, the heater is immediately switched off and a fault code is recorded. 

 

When the heater is switched off, the green light goes off and fuel is no longer fed to the burner. The glow plug remains switched on for 30 seconds to clear the heater of combustible residue. To prevent damage to the heater, the blower continues to run until the heater is cool.

Shown on TX GatorShown on TX Gator
#

Features of the sunshade:

  • Made from 100 percent solution dyed, all-weather ultraviolet resistant polyester designed specifically to handle stress and resist tearing.
  • Urethane coating is added to the fabric, adding stability and increased moisture and mildew resistance, with minimal shrinking or stretching.
  • Heavy-duty powder coated black steel frame that bolts directly to the vehicle chassis.
  • Sunshade dimensions: 864 mm by 1270 mm (34 in. by 50 in.)
  • Not compatible with side storage box
Visor kitVisor kit

The conveniently placed overhead visor provides sun protection.

 

It is compatible with the following vehicles:

  • All Gator model year 2011-current XUV 625i, XUV 825i, XUV 855D, and M-Gator™ A2 Utility Vehicles when equipped with a deluxe cab frame
  • All Gator HPX model year 2004-current, XUV 620i, and XUV 850D Utility Vehicles when equipped with a deluxe cab frame
  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab
  • M-Gato A1 when equipped with a hard-door cab
Windscreen kitWindscreen kit

The windscreen is constructed of tough, 4.76-mm (3/16-in.) thick tinted acrylic.

  • Easily attaches to and detaches from the vehicle
  • Height can be set to accommodate the operator preference
Dimensions

 

 Width

 940 mm (37 in.)

 Height

 457 mm (18 in.)

 Depth

 127 mm (5 in.)

Rear Receiver Hitch

Seat

Adjustable driver seat—forward positionAdjustable driver seat—forward position
Adjustable driver seat—aft positionAdjustable driver seat—aft position

This kit provides a slide-rail system that allows five 14-mm (9/16-in.) fore-aft positions.

Spark Arrester

Spark arresterSpark arrester

Allows the Gator™ TX Turf to meet specific regulatory requirements.

Speed Control

Rough terrain kitRough terrain kit

Ideal for operators who are consistently driving over rough terrain. The damper assists the operator by modulating throttle input.

Compatible with Gator™ TS, TX, TH, and M-Gator™ A1 Utility Vehicles.

Sprayers

45-gal. (170- L) Tow-Behind Sprayer45-gal. (170- L) Tow-Behind Sprayer

The HP 45-gal. (170-L) Tow-Behind Sprayer offers the ultimate in performance and versatility. With a 45-gal. capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and deicer. It is the perfect match for the customer who wants extreme performance. 

 

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction and have a low profile, which maintains a low center of gravity for excellent stability. Cover ground quickly with flexible boom options; a 150 in. (3.8 m) precision folding, 120-in. (3-m) standard three tip, 24-ft (7.3-m) boomless, or no boom at all (boom sold separately).

HP features:
  • 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
  • Premium pistol grip spray gun, designed for single hand mist to 35 ft (10.7 m) stream
  • Front-mount hose tender for easy hose access and storage
  • Glycerin filled pressure gauge
  • TeeJet™ pressure regulation/recirculation valve
  • Includes sprayer remote control
Additional features
  • Easy boom removal for added convenience
  • Control valve channels spray to either the boom or spray wand
  • Rugged translucent yellow tank with molded fill level indicators (in gal.)
Boom options (sold separately):
  • 150-in. (3810-mm) precision spray boom
  • 24-ft  (288-in.) boomless spray nozzles

 

SHURflo is trademark of SHURflo, LLC. TeeJet is a registered trademark of Spraying Systems Company.

45-gal. (170-L) tow-behind sprayer 45-gal. (170-L) tow-behind sprayer

The 45-gal. (170-L)  trail-type sprayer is equipped with a boom that sprays a wide, 120-in. width.

  • Three nozzles for efficient broadcast spraying
  • Boom folds up against the tank for storage

A 20-ft hose and handgun are provided.

  • The 20-ft hose and handgun are helpful when spraying trees or other remote areas that cannot be reached with the sprayer itself
  • A 14-in. wand on the handgun is standard equipment

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction.

  • Low center of gravity gives excellent stability
  • Equipped with a 4-position hitch
  • Rear of the frame is designed so the sprayer will stand upright during storage to reduce the amount of space required

Additional features include:

  • Diaphragm-type pump designed for high-hour commercial applications; it can be run dry without damage
  • The spray wand is constructed of non-corrosive polypropylene material with Viton® components for remote spray jobs
  • Two-wire fused wiring harness complete with quick-disconnects for convenient electrical hookup
  • Large cap to easily fill up the tank
  • Control valve to channel the spray to the boom or handgun
  • Rugged translucent yellow tank with molded fill-level indicators (in gallons)
Specifications

Capacity

45 U.S. gal. (170 L)

Pump

Type

Electric motor
and diaphragm

Manufacturer

SHURflo® 

Operating pressure

100 psi

Current draw

7 amp

Valve material

Viton® 

Diaphragm material

Santoprene™

Strainer

Stainless steel

Boom spray width

120 in. (305 cm)

Spray tip(s)

Three #11008VP

Spray flow rate

2.1 U.S. gpm (7.9 L/min)

Remote spray method

20-ft hose with adjustable polypropylene handgun with 14-in. wand

Handgun material

Polypropylene with Viton components

Adjustment

Fan-to-stream

Tires

15x6-6 pneumatic

Wheel bearings

Roller bearings

Axle diameter

1 in. (2.5 cm)

Hitch

Pin and spring clip, four height positions

Weight - empty

80 lb (36.3 kg)

Weight - full

456 lb (207 kg)


Compatible with all Gator models except XUV 550, XUV 550 S4, and RSX Utility Vehicles.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

45-gal. (170-L) tow-behind sprayer
Order number: LP20485

 

SHURflo is a U.S.-registered trademark of SHURflo, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

Sprayers

45-gal. (170-L) Gator bed sprayer45-gal. (170-L) Gator bed sprayer
#

The 45-gal. (170-L) Gator bed sprayer is designed to work with the Gator vehicles equipped with the steel bed or deluxe cargo box. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 43-in. boom that sprays a 120-in. swath. It's equipped with a 20-ft hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable brass spray wand tip achieves streams up to 30 ft. It comes equipped with rubber feet and custom brackets, which secure to the Gator bed, for a no tools mount.

 

Special features:

  • 45-gal. (170-L) capacity
  • Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
  • Brackets allow boom height adjustment
  • 100 psi SHURflo diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage
  • The fully adjustable brass spray wand tip achieves streams up to 30 ft
  • Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
  • Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
  • On/off switch located near operator
  • Easy boom removal for added convenience
  • Control valve channels spray to either the boom or spray wand
  • 12-V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
  • Rugged translucent yellow tank with molded fill level indicators (in gallons)
Specifications

Capacity

45 U.S. gal. (170 L)

Pump

Type

Electric motor and diaphragm

Manufacturer

SHURflo® 

Operating pressure

100 psi

Current draw

7 amp

Valve material

Viton® 

Diaphragm material

Santoprene™

Spray flow rate

2.1 U.S. gpm (8 L/min)

Sump strainer

Stainless steel

Remote spray method

Spray wand

Polypropylene with Viton components

Tip material

Brass

AdjustmentFan-to-stream
Hose length20-ft nylon reinforced rubber

Boom

Boom width43-in. (109 cm) fixed
Spray swath120-in. (305 cm)
Spray tip(s)Three - TF-VP3

Mounting

Steel bedCustom tailgate clamp mounting
Deluxe cargo boxCustom brackets secure to tie-downs

Compatibility

All Gator models except CX

Shipping weight

68 lb (31 kg)

Net weight

64 lb (29 kg)

 

Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

45-gal. (170-L) Gator bed sprayer
Order number: LP20852

 

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

High-performance 45-gal. (170-L) Gator bed sprayerHigh-performance 45-gal. (170-L) Gator bed sprayer
#

The high-performance Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box or steel bed. With a 45-gal. (170-L) capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and de-icer. Engineered brackets secure the sprayer to the Gator bed with no tools, or additional tie-downs required.

NOTE: Sprayer shown above with optional 150-in. precision boom (LP22885).

High-performance features:

  • 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
  • Premium pistol grip spray gun, designed for single hand mist to 35-ft stream
  • Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
  • Glycerin-filled pressure gauge and TeeJet™ pressure regulation/recirculation valve
  • Choice of booms (sold separately)
  • On/off capabilities in the palm of your hand with the included sprayer remote control (LP22912)
  • 12V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
  • Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
  • Control valve channels spray to either the boom or spray wand
  • Rugged translucent yellow tank with molded fill level indicators (in gallons)
Specifications

Capacity

45 U.S. gal. (170 L)

Pump

Type

Electric motor and diaphragm

Manufacturer

SHURflo® 

Operating pressure

45 psi

Current draw

7 amp

Valve material

Viton® 

Diaphragm material

Santoprene™

Spray flow rate

3.6 U.S. gpm (13.6 L/min)

Sump strainer

Stainless steel

Remote spray method

Spray wand

Poly, alloy, and brass with Viton components

Tip material

Brass and stainless

AdjustmentFan-to-stream
Hose length20-ft - 1/2-in. nylon reinforced rubber

Gauge

Glycerin filled

Spray control

Pressure regulation/recirculation

Remote control

12V receiver with dual FOB remote on/off

Boom (sold seperately)

Option 1150-in. spray width precision folding (5 tip)
Option 2120-in. spray width (3 tip)
Option 324-ft boomless nozzle

Mounting

Steel bedCustom tailgate clamp mounting
Deluxe cargo boxCustom brackets secure to tie-downs

Compatibility

All Gator models (except CX)

Shipping weight

56 lb (25 kg)

Net weight

52 lb (23 kg)

 

Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

High-performance 45-gal. (170-L) Gator bed sprayer
Order number: LP22908

 

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

25-gal. (95-L) Gator bed sprayer25-gal. (95-L) Gator bed sprayer

The improved 25-gal. (95-L) Gator bed sprayer is designed to work with all steel bed and deluxe cargo box Gator Utility Vehicles (except CX), and provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 109-cm (43-in.) boom that sprays a 304.8 cm (120-in.) swath. It is equipped with a 5.8-m (19-ft) hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable brass spray wand tip achieves streams up to 9.1 m (30 ft). Engineered brackets secure the unit to Gator bed with no tools or additional strapping required.

Features include:

  • Brackets secure to the Gator bed with no additional strapping or bungees required
  • Brackets allow boom height adjustment
  • 100 psi Shurflo® diaphragm-type pump is designed for high hour commercial applications - it can be run dry without damage
  • The fully adjustable brass spray wand tip achieves streams up to 9.1 m (30 ft)
  • Equipped with a 5.8-m (19-ft) hand wand hose
  • Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
  • On/off switch located near operator, 12-V plug included complete with quick-disconnects, for convenient electrical hookup
  • Easy boom removal for added convenience
  • Control valve channels spray to either the boom or spray wand
  • Rugged translucent yellow tank with molded fill level indicators (in gallons)
Specifications

Capacity

25 U.S. gal. (95 L)

Pump

Type

Electric motor and diaphragm

Manufacturer

SHURflo

Operating pressure

100 psi

Current draw

7 amp

Valve material

Viton®

Diaphragm material

Santoprene™

Strainer

Stainless steel

Boom spray width 

120 in. (305 cm)

Spray tip(s)

Three TF-VP3

Spray flow rate

2.1 U.S. gpm (7.9 L/min)

Remote spray

19-ft hose with adjustable polypropylene handgun with 14-in. wand

Handgun material

Polypropylene with Viton components

Adjustment

Fan-to-stream

Shipping weight 

40 lb (18 kg)

Warranty 

Two year

 

Ordering information

Contact the local John Deere dealer for availability and pricing information.

 

25-gal. (95-L) Gator bed sprayer
Order number: LP33597

 

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

GatorPal model GP-2700GH shown – view oneGatorPal model GP-2700GH shown – view one
GatorPal model GP-2700GH shown – view twoGatorPal model GP-2700GH shown – view two

The GatorPal custom designed washers are designed to exact dimensions of the John Deere Gator™. These belt-driven, industrial-duty units include a water tank and 100-ft hose reel, and are perfect for cleaning in remote or hard-to-access areas where water is not readily available.

 

Features:

  • 196-cc Honda™ OHV engine
  • 2700 psi
  • 2.4 gpm
  • For Gator weight capacities up to 600 lb maximum
  • 35-gal. holding tank
  • 100-ft hose reel
  • Performance-proven engine with low-oil protection
  • Belt-drive triplex piston crankshaft pump with ceramic plungers
  • Thermal relief valve
  • Adjustable pressure
  • Forged brass manifold
  • Corrosion-resistant aluminum frame and fork-lift-accessible plastic pallet
  • Quick-connect nozzles (0, 15, 25 and 40 degree)
  • 3/8-in. x 100-ft non-marking hose with quick connects, swivel, and bend restrictors
  • 36-in. lance with rubber grip
  • Professional-grade insulated trigger gun with safety lock-off
  • Two year warranty (five years on pump)

Fits on TX, TH 6x4, HPX, XUV 825i, 825i S4, 855D, and 855D S4 Gators.

Honda is a U.S.-registered trademark of Honda Motor Company.

Ordering information
Please contact your local John Deere dealer for availability and pricing information.

John Deere GatorPal portable high-pressure washer
Order number: LPGP2700GH

GatorPal model GP-2700GH shownGatorPal model GP-2700GH shown
GatorPal model GP-2700GH shownGatorPal model GP-2700GH shown

The GatorPal custom designed washers are designed to exact dimensions of the John Deere Gator™ Utility Vehicle. These belt-driven, industrial-duty units include a water tank and 100-ft hose reel, and are perfect for cleaning in remote or hard-to-access areas where water is not readily available.
 
Features:

  • 196-cc Subaru™ OHV engine
  • 2700 psi
  • 2.4 gpm
  • For Gator weight capacities up to 600 lb maximum
  • 35-gal. holding tank
  • 100-ft hose reel
  • Performance-proven engine with low-oil protection
  • Belt-drive triplex piston crankshaft pump with ceramic plungers
  • Thermal relief valve
  • Adjustable pressure
  • Forged brass manifold
  • Corrosion-resistant aluminum frame and fork-lift-accessible plastic pallet
  • Quick-connect nozzles (0, 15, 25 and 40 degree)
  • 3/8-in. x 100-ft non-marking hose with quick connects, swivel, and bend restrictors
  • 36-in. lance with rubber grip
  • Professional-grade insulated trigger gun with safety lock-off
  • Two year warranty (five years on pump)

 

Fits on TX, TH 6x4, HPX, XUV 625i, 825i, 825i S4, 855D, and 855D S4 Gators.

 

Subaru is a U.S.-registered trademark of Subaru Motor Company.

Ordering information
Please contact your local John Deere dealer for availability and pricing information.  Mi-T-M direct order.

 

John Deere GatorPal portable high-pressure washer
Order number: LPGP2700GS

Shown on TH 6x4 with HP 45-gal. SprayerShown on TH 6x4 with HP 45-gal. Sprayer

The standard Gator boom is compatible with all Gator sprayer models and is sold separately for the HP Gator sprayers. This fixed boom is conveniently sized at 43 in. (1.1 m) and does not extend wider than the Gator bed, but it is perfect for covering ground quickly and thoroughly with a 120-in. (3-m) spray swath.

 

The boom is ideal for basic spraying application. Three tips and check valves round out this offering (boom only, mounting brackets are provided with sprayers).

Boom Features:
  • 43-in. (1.1-m) boom with three tips
  • Check valves prevent siphoning and dripping
  • Sold separately for:
    • HP 45-gal. Gator Bed Sprayer
    • HP 90-gal. Gator Bed Sprayer
    • HP 45-gal. Gator Bed Sprayer – XUV 550
Shown on TH 6x4 with HP 45-gal. SprayerShown on TH 6x4 with HP 45-gal. Sprayer
Shown on TH 6x4 with HP 45-gal. SprayerShown on TH 6x4 with HP 45-gal. Sprayer

The 150-in. (3.81-m) precision boom is compatible with the HP sprayers. This folding boom is made to cover ground quickly and thoroughly with five precision spray tips, TeeJet™ nozzle bodies and commercial grade diaphragm check valves. The outer tips offer versatility with built-in shut offs to allow an adjustable 90-in. (2.3-m), 120-in. (3-m), or 150-in. (3.8-m) spray swath.

150-in. (3.8-m) precision boom features:
  • Folding spring hinge
  • Breakaway design
  • Five TeeJet tips and nozzle bodies
  • Adjustable spray swath (90 in., 120 in., 150 in.)
  • 1/2-in. industrial-grade rubber hose
  • Designed to work with
    • HP 45-gal. Gator™ Bed Sprayer
    • HP 90-gal. Gator Bed Sprayer
    • HP 45-gal. Gator Bed Sprayer – XUV 550

 

 

 

TeeJet is a registered trademark of Spraying Systems Company.

Shown on TH 6x4 with HP 90-gal. SprayerShown on TH 6x4 with HP 90-gal. Sprayer
HP 90-gal. SprayerHP 90-gal. Sprayer

The 24-ft (7.3-m) boomless spray nozzles are compatible with all HP sprayers. This boom is perfect for covering ground quickly and thoroughly with a 24-ft (7.3-m) spray swath. It is ideal for uneven terrain or where precision spray application is not necessary. TeeJet™ nozzle bodies and commercial grade diaphragm check valves round out this offering.

Boomless spray nozzles feature
  • Three TeeJet tips and nozzle bodies
  • Commercial-grade diaphragm check valves
  • 1/2-in. (12.7-mm) industrial-grade rubber hose
  • Designed to work with all HP sprayers :
  • HP 45-gal. Gator™ Bed Sprayer
  • HP 90-gal. Gator Bed Sprayer
  • HP 45-gal. Gator Bed Sprayer – XUV 550

 

 

 

 TeeJet is a registered trademark of Spraying Systems Company.

Spreaders

17AT Cart17AT Cart
  • 17-ft3 capacity
  • 1000-lb load limit
  • Copolymer polypropylene is compression molded for optimum thickness in all areas and maximum durability
  • Heavy-duty, reinforced structural frame with a 25.4-mm (1-in.) diameter, one-piece axle to handle weight, speed, and bumps
  • Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
  • Double-sealed, high-speed roller bearings to handle a 48-km/h (30-mph) maximum speed
  • Heavy-duty polyethylene bed
    • Accepts dividers to separate cargo (template included)
  • All-terrain knobby tires
    • Provides good flotation and traction in mud, sand, and other wet or soft areas
    • Flexes over bumps and ruts for a smoother, more controlled ride
    • Minimizes ground compaction to save turf and prevent ruts in soft ground
  • Poly fenders to keep the operator, cart, and vehicle clean
  • Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1-7/8-in.) ball hitch, including Gator™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
  • Quality and styling compatible with other John Deere equipment
Ordering information

Contact the local John Deere dealer for availability and pricing information.

17AT Cart

Order number: LPPCT17ATJD

Fertilizer spreaderFertilizer spreader
#

The Gator™ electric fertilizer spreader is the ideal solution for medium to large size jobs. This unit is engineered to fit heavy-duty XUV Gator Utility Vehicles and designed with a versatile hitch mechanism (sold separately) that allows quick and secure attach/detach capability for easy bed access or switching to a Gator salt spreader. Convenience is at the operator’s fingertips with an electronic variable-speed spinner and electronic gate control from the Gator seat. Adjustable flighting allows spread pattern control to make sure the material is applied where it is needed.

 

Features:

  • Powder-coated steel frame
  • Electronic variable-speed spinner
  • Electrically actuated control of the flow gate
  • 10-in. (25.4-cm) diameter spinner is stainless steel with adjustable flighting to control spreader pattern
  • 8:1 ratio with bronze gear, grease filled
  • Motor is 1/3 hp, 12-V DC, semi sealed

The mounting hitch and control box are sold separately, available through Order Zone.

 

Ideal for:

  • Granular fertilizer
  • Seed
  • Granular pesticide
  • Granular herbicide

Capacity:

  • Volume: 3.0 cu ft (0.1 cu m)
  • Weight: 240 lb (108.9 kg)
  • Spreading width: up to 20 ft (6.1 m)

Includes:

  • Side deflector

Compatibility:

  • Compatible with all model year 2011 to current heavy-duty Gator XUV 625i, 825i, 825i S4, 855D, and 855D S4 Utility Vehicles.
  • Compatible with all XUV560 and XUV560 S4 Utility Vehicles.
  • Gator XUV 620i and 850D Utility Vehicles and XUV 625i, 825i, and 855D Utility Vehicles pre model year 2011 must purchase the Gator hitch-mounting brackets, sold separately through Order Zone.

Ordering information

Available through Order Zone. Contact the local John Deere dealer for availability and pricing information.

Salt spreaderSalt spreader
#

The Gator™ electric salt spreader is the ideal solution for medium to large size jobs. This unit is engineered to fit heavy-duty XUV Gator vehicles and designed with a versatile hitch mechanism (sold separately) that allows quick and secure attach/detach capability for easy bed access or switching to a Gator fertilizer spreader. The Gator salt spreader features an electric-driven auger for consistent salt presentation to the spinner. It draws power from the Gator vehicle, so no external power source is needed. It is powered by a variable-speed controller (sold with hitch) for precise spread pattern control. 

 

Features:

  • Powder-coated steel frame
  • Spinner motor controlled using the vehicle’s 12-V system
  • 10-in. (25.4-cm) diameter spinner is nylon/glass reinforced resin for ultimate corrosion resistance
  • 5:1 ratio with bronze gear, grease filled
  • Motor is 1/3 hp, 12-V DC, semi sealed

The mounting hitch and control box are sold separately. Available through Order Zone.

 

Ideal for:

  • Salt and large granular materials

Capacity:

  • Volume: 3.0 cu ft (0.1 cu m)
  • Weight: 240 lb (108.9 kg)
  • Spreading width: Up to 20 ft (6.1 m)

Compatibility:

  • Compatible with all model year 2011 to current heavy-duty XUV 625i, 825i, 825i S4, 855D, and 855D S4 Utility Vehicles.
  • Compatible with all Gator XUV560 and XUV560 S4 Utility Vehicles.

Gator XUV 620i and 850D Utility Vehicles and XUV 625i, 825i, and 855D Utility Vehicles pre model year 2011 must purchase the Gator hitch mounting brackets, sold separately through Order Zone.

Ordering information

Available through Order Zone. Contact the local John Deere dealer for availability and pricing information.

TX hitch and control boxTX hitch and control box

The spreader hitch and control kits were designed to mount salt and fertilizer spreaders which are engineered to fit Gator™ Utility Vehicles.

 

Features:

  • Hitch frames are spring loaded for quick attach/detach spreader capabilities
  • Hitch can be easily lowered by the use of spring-loaded pins, promoting easy bed or engine access
  • Electronic control box is weather resistant and enables variable-speed application from the comfort of the operator’s seat

Spreader hitch and controls kit includes:

  • Spreader hitch frame
  • Electronic control box and wiring

Storage

Deluxe Gator gear organizer (shown in black)Deluxe Gator gear organizer (shown in black)
#

Increase and organize cargo box capacity with the soft, weather-protective deluxe Gator gear organizer. The organizer installs easily on the load guard directly behind the operator's station. It is compatible with Gator Utility Vehicles equipped with the all-new deluxe cargo box.

Compatible with all model year 2011 - current Gator XUV 625i, XUV 825i, XUV 855D, TX, TX Turf, TH 6X4, TE, M-Gator™ A2, and M-Gator A3 Utility Vehicles.

Compatible with all model year 2013 - current Gator XUV 825i S4 and XUV 855D S4 Utility Vehicles.

Ordering information
Please contact your local John Deere dealer for availability and pricing information.

Deluxe Gator gear organizer - Camo
Order number: LP19877

Gator toolbox shown on TH 6x4 with deluxe cargo boxGator toolbox shown on TH 6x4 with deluxe cargo box
Gator toolbox - openGator toolbox - open

Quality constructed from 16 gauge steel, this industrial tool box is durable enough to handle wear and tear even from the toughest contractors. This tool box keeps tools, equipment, and other valuables secure, clean, dry, and protected from outside elements - due to full weather seal locks and a rust-resistant, powder-coat paint application. Twin commercial-grade gas shocks automatically lift lid for effortless one-handed open/close. Comes complete with key locks to guard against theft.

Product attributes:

  • Two lids hinged at the middle allows access from both sides of the vehicle
  • Extra-wide lid opening allows easy access to tools and valuables
  • Key locks guard against theft (two keys provided)
  • Compatible with Gator TX, TH, TE, XUV 625i, XUV 825i/E/M, XUV 825i/E/M S4, XUV 855D/E/M, and XUV 855D/E/M S4, XUV835E/M/R, XUV865E/M/R Utility Vehicles equipped with the deluxe cargo box as shown in the picture above
  • Also compatible with Model Year 2018 and newer HPX615 and HPX815

Ordering information
Please contact your local John Deere dealer for availability and pricing information.

Gator tool box
Order number: LP19886

Side-door opening toolbox Side-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

 

Side-door opening toolbox features:

  • 125-L (33-gal.) sealed storage
  • Heavy-gauge sheet metal
  • D-rings for tie downs
  • Fully sealed lockable latch
  • Sealed door
  • Door can also be used as a work bench when down
  • Can be mounted on either side of the cargo box

 

Side-door opening toolbox

Toolbox weight

29 kg (64 lb)

Toolbox capacity

34 kg (75 lb)

Toolbox dimensions

-Full box: 109.4-cm (43.1-in.) long X 35-cm (13.8–in.) wide X 32.5-cm (12.8–in.) tall

-125-L (33-gal) total volume

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate, and bolting the toolbox onto the cargo box.

 

The toolbox requires the tailgate with brake and tail lights kit (BM26161) and optional label kit:

  • BM26220 – green and yellow
  • BM26218 – olive and black
  • BM26219 – camo

This toolbox is compatible with the following Gator™ Utility Vehicle models:

  • TX
  • TX Turf
  • TE
  • TH
  • XUV625i
  • XUV825i/E/M
  • XUV825i/E/M S4
  • XUV855D/E/M
  • XUV855D/E/M S4
  • XUV835E/M/R
  • XUV865E/M/R
  • Model Year 2018 and newer HPX615 and HPX815
Top-door opening toolboxTop-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

 

Top door opening toolbox features:

  • 125-L (33-gal.) sealed storage
  • Heavy-gauge sheet metal
  • D-rings for tie downs
  • Fully sealed lockable latch
  • Sealed door
  • Toolbox divider
  • Removable tool tray
  • Can be mounted on either side of the cargo box

 

Top door opening toolbox

Toolbox weight

32.7 kg (72 lb)

Toolbox capacity

32.7 kg (75 lb)

Toolbox dimensions

-Tray: 27.4-cm (10.8-in.) long x 21.8-cm (8.6-in.) wide x 7.1-cm (2.8–in.) deep -Left-hand side compartment: 46.2-cm (18.2–in.) long X 32.5-cm (12.8–in.) wide X 35.3-cm (13.9–in.) tall -Right-hand side compartment: 62.7-cm (24.7–in.) long X 32.5-cm (12.8–in.) wide X 35.3-cm (13.9-in.) tall

-125-L (33-gal.) total volume

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate, and bolting the toolbox onto the cargo box.

 

The toolbox requires the tailgate with brake and tail lights kit (BM26161) and optional label kit:

  • BM26220 – green and yellow
  • BM26218 –olive and black
  • BM26219 – Camo

This toolbox is compatible with the following Gator™ Utility Vehicle models:

  • TX
  • TX Turf
  • TE
  • TH
  • XUV625i
  • XUV825i/E/M
  • XUV825i/E/M S4
  • XUV855D/E/M
  • XUV855D/E/M S4
  • XUV835E/M/R
  • XUV865E/M/R
  • Model year 2018 and newer HPX615 and HPX815

Suspension

Heavy-duty front suspension kitHeavy-duty front suspension kit

The heavy-duty front suspension kit improves ride and handling while hauling heavier loads.

  • Heavy-duty front shock absorbers with higher-strength springs replace the standard shocks
  • Spring support is adjustable to five positions
  • Heavy-duty suspension kit is recommended if the Gator™ utility vehicle is equipped with a cab or front blade attachment
    • The front blade attachment is not compatible with TH 6X4 Diesel Utility Vehicles.

NOTE: The M141507 wrench to adjust the weight setting is available through Service Parts.

Tire Chains

Tire chainsTire chains

Tire chains increase traction dramatically under ice and snow conditions.

NOTE: Not intended for use on all four rear tires on the TH 6x4.

Winch

Warn Winch (3000 lb)Warn Winch (3000 lb)
#

This strong, 12-V winch has an impressive pulling capacity of 3000 lb (1361 kg). It is equipped with a water-resistant contactor that supplies the amperage required for higher pulling capacities. The winch also includes a special wiring harness that allows a quick connection to the 12-V power supply at the front of the Gator™. The rear wiring harness with quick connection can be purchased through Parts.
 
The winch has a 10-ft lead and a water-resistant remote for safe-distance operation. It also comes with a four-way roller fairlead to minimize rope abrasion and pulling resistance.

The kit comes with the winch, receiver mounting plate, and wiring for front mount. This winch is compatible with 1-1/4-in. front and rear receiver hitches.

NOTE: Requires front receiver hitch for front mount. Requires rear receiver hitch for rear mount. Requires AM137110 rear multi-mount harness for rear mount. VGA10459 144-in. battery cable is required for TH 6X4 Gas, TH 6X4 Diesel, and M-Gator™ A1 Utility Vehicles.

Standard featuresStandard features
Remote control is included in the standard featuresRemote control is included in the standard features

 

A - Centered winch drum
B - Sealed all-metal drivetrain
C - Ergonomic clutch handle
D - Disc brake
E - Updated drum supports
F - Roller fairlead
G - Sealed winch motor

A - Hand-held remote with 3.0-m (10-ft) lead

 

 

 

 

 

 

Specifications

 

3000-lb winch

 Rated pulling capacity 3000 lb (1361 kg)
 All metal drivetrain Three-stage planetary
 Sealed drivetrain Yes
 Sealed winch motor 12-VDC, permanent magnet
 Centered winch drum Yes
 Drum diameter/length 2.0 in./2.9 in. (52 mm/74 mm)

 Rope

 50-ft aircraft-grade wire, 3/16-in. diameter (15-m, 5-mm  diameter)

 Mechanical brake Disc brake
 Gear ratio 154:1
 Clutch (freespooling) Sliding pin and ring gear
 Mini-rocker switch Yes
 Handheld remote Yes
 Sealed contactor Yes
 Winch weight 15.6 lb (7.1 kg)
 Winch dimensions 13.12-in. length by 4.51-in. diameter by 4.69-in. height (33.3-cm length by 11.5-cm diameter by 11.9-cm height)
 Winch wiring 6 gauge
 Amp draw at 3000 lb 198 amps

 

Warn is a U.S.-registered trademark of Warn Industries Incorporated.

Winch accessories kitWinch accessories kit

Double the pulling power, change the pulling direction, and keep the winch in proper working order.

The accessories kit is essential gear for operators getting the most out of their winch:

  • Effectively anchors to trees/boulders
  • Change the pulling direction
  • Double the pulling capacity

The accessories kit includes:

  • Flexible tree strap
  • Snatch block
  • Shackle

Each kit comes in a black Cordura® heavyweight-nylon soft case.

 

Cordura is a trademark of INVISTA.

Windshield

Especially useful for working around properties and job sites, the windshield washer kit includes the following:

  • Mounting bracket
  • Hardware
  • Spray nozzle
  • Large reservoir with electric pump
  • Harness and hose

The reservoir assembly bolts to the bottom-right rear of the cab structure. A convenient overhead-mounted on/off rocker switch controls the windshield wiper and washer fluid. As with all Gator™ electrical kits, the washer kit ties into the vehicle's wiring harness for quick installation.

Compatible with the following vehicles:

  • Traditional Series—TS, TX, TX Turf, and TH 6x4 when equipped with a soft-door or hard-door cab and electrical kit
    • TH 6x4 Diesel requires cargo box power lift
  • M-Gator A1 when equipped with a hard-door cab and electrical kit

Kit includes:

  • Wiper
  • Motor assembly
  • Mounting hardware

A convenient overhead mounted on/off rocker switch controls the windshield wiper and washer fluid (if equipped). As with all Gator™ electrical kits, the wiper kit ties into the vehicle's wiring harness for quick installation.

Compatible with the following vehicles:

  • Traditional Series—TS, TX, TX Turf, and TH 6x4—when equipped with a soft-door or hard-door cab and electrical kit
  • M-Gator™ A1 when equipped with a hard-door cab and electrical kit